Minicom Advanced Systems Smart 4 Guide de l'utilisateur Page 69
- Page / 92
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Figure
Configuring Security Settings
The OSD comes with an advanced password security system that contains three
different security levels. Each security level has different
as follows:
Administrator (Status A)
Set and modify all passwords and security profiles
Fully access any computer
Use all OSD functions
Supervisor (Status S)
who can:
Fully access any computer
Access the following OSD
the Confirmation label.
User (Status U) –
There are
Each User has a Profile set by the Administrator that defines the access level to
different computers.
There are
6.2.7 on page 73.
Activating Password Protection
By default,
OSD access is not password protected. Only the Administrator can
password-
protect the OSD or disable password protection.
To activate password protection:
1. In
the General settings window
2.
Press the Space bar to toggle between Security On
The password dialog box appears.
3.
Type the Administrator’s password (default is “admin”).
Operating
the SmartRack 116 IP Switching System Locally
Figure
76 – General Settings Window
Configuring Security Settings
The OSD comes with an advanced password security system that contains three
different security levels. Each security level has different
access rights to the system,
Administrator (Status A)
who can:
Set and modify all passwords and security profiles
Fully access any computer
Use all OSD functions
who can:
Fully access any computer
Access the following OSD
functions only –
F4 Scan, F5 Tune, and F6 Moving
the Confirmation label.
There are
six different Users in the
SmartRack 116 IP
Each User has a Profile set by the Administrator that defines the access level to
There are
three different access levels –
explained
Activating Password Protection
OSD access is not password protected. Only the Administrator can
protect the OSD or disable password protection.
To activate password protection:
the General settings window
(see Figure 76), navigate to the
Security
Press the Space bar to toggle between Security On
and Off.
The password dialog box appears.
Type the Administrator’s password (default is “admin”).
the SmartRack 116 IP Switching System Locally
Using the OSD
User Guide | 69
The OSD comes with an advanced password security system that contains three
access rights to the system,
F4 Scan, F5 Tune, and F6 Moving
SmartRack 116 IP
system.
Each User has a Profile set by the Administrator that defines the access level to
explained
in Section
OSD access is not password protected. Only the Administrator can
Security
line.
- SmartRack 116 IP 1
- User Guide 1
- Legal Notice 2
- About this Document 3
- Style Conventions 4
- Table of Contents 5
- User Guide 7
- Table of Figures 10
- User Guide 11
- 1 Introduction 12
- 1.2 Terminology 13
- 1.3 Compatibility 13
- 1.5 Technical Precautions 13
- 1.7 Trademarks 14
- 1.8 WEEE Compliance 14
- 1.6 Safety 14
- 2 Installation 15
- Installation 16
- System Components 16
- 16 16
- The SmartRack 116 IP Unit 17
- Pre-Installation Guidelines 18
- 18 18
- Replacing the Bracket 19
- Connecting 20
- User Guide 21
- 22 22
- 2.5 Connecting the System 23
- 2.6 Connecting to the Servers 23
- Connecting a RICC/ROC PS/2 24
- Connecting a RICC 25
- /ROC USB 25
- Connecting a RICC SUN 26
- User Guide 27
- 3 Configuring the Network 28
- Interface 29
- Configuring the Network 30
- 30 30
- User Guide 31
- 32 32
- 3.3.2 Configuring 33
- Adding a User 34
- Configuring User Settings 35
- User Guide 35
- Deleting User(s) 36
- Blocking a User 36
- Editing User 36
- Information 36
- Configuring the KVM Switch 37
- 38 38
- Installing 40
- Upgrading Firmware 40
- User Guide 41
- 3.9 Reloading a 42
- 44 44
- Conducting 45
- Conducting a Remote Session 46
- Starting a Remote Session 46
- 46 46
- 4.2 Sharing a Remote Session 47
- Exclusive 48
- Full Screen Mode 49
- Verifying 50
- 50 50
- Adjusting the Video 52
- Manually 53
- Adjusting Video Settings 53
- Managing Keyboard Sequences 54
- User Guide 55
- Recording a New Custom Key 56
- Editing a Key Sequence 56
- Synchronizing Mouse Pointers 57
- 58 58
- The USB Option 59
- Aligning the M 60
- Pointers 60
- Calibrating Mouse 61
- 5 Troubleshooting – Safe Mode 62
- Restoring Factory Defaults 63
- Restoring the Device Firmware 64
- Figure 73 – Upgrade Succeeded 65
- Operating 66
- Using the Keyboard Hotkeys 66
- 66 66
- 6.2.3 Configuring t 67
- Configuring Security Settings 69
- Operating the SmartR 70
- Using the OSD 70
- 70 70
- Configuring the Port 71
- Configuring the T 72
- Configuring the Users 73
- Settings 73
- 74 74
- OSD Functions 75
- Scanning 76
- Computers (F4) 76
- Tuning (F5) 76
- Moving the Label ( F6) 77
- 78 78
- Starting and C 80
- Software 80
- Verifying the V 81
- RICC/ROC Version 82
- Obtaining N 83
- Firmware 83
- Troubleshooting 84
- – Update Software 84
- 6.4.4 Electricity F 85
- 86 86
- 7 Technical Specifications 87
- Technical Specifications 88
- 88 88
- User Guide 89
- 9 SNMP Events Table 90
- SNMP Events Table 91
- User Guide 91
- 201204210 • 933213_EN 92
Produits connexes et manuels pour Mise en réseau Minicom Advanced Systems Smart 4
(92 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.449 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels